PCHardwareTest guide

Mouse Test Online

Move, click and scroll inside the test area to light up the left, right, middle, button 4, button 5, scroll and double-click indicators while live coordinates, the last wheel delta and an estimated polling rate update beside them. It is a quick way to check a worn mouse button, a skipping wheel or the side buttons of a gaming mouse without installing vendor software.

Start Mouse Test Online

Mouse Test Online

Move, click and scroll inside the test area.

Not started
LEFT RIGHT MIDDLE BUTTON 4 BUTTON 5 SCROLL DOUBLE-CLICK
Coordinates —
Wheel delta (last) —
Browser-estimated polling —

Polling rate is a rough, browser-side estimate based on event timing, not a certified hardware measurement.

Reading the mouse indicators

Each chip lights up when the matching event arrives, so a button that never lights is not reaching the browser. Coordinates show the pointer position inside the test area. The wheel delta shows the size and sign of the last scroll step: if the sign flips while you keep scrolling one way, dirt in the wheel encoder is a likely cause.

The polling figure is a rough estimate from event timing, not a certified measurement. Use it to compare two mice or two USB ports on the same computer rather than as a spec.

Mouse button, double-click and scroll wheel test

  1. Press left, right and the wheel button once each.
  2. Press the two side buttons. If Button 4 or 5 never lights, vendor software or the OS may be remapping it to back and forward.
  3. Double-click quickly, then click once slowly. A slow single click that sets the double-click chip suggests a bouncing switch.
  4. Scroll up and then down in slow steps and watch the delta values.

Wired, wireless and gaming mice

Wireless mice can lag on the first movement after sleeping, so move the mouse for a moment before judging it. For a gaming mouse, switch off any profile that rewrites buttons so you see raw input. DPI changes show up only as faster coordinate movement; the page cannot display a DPI number.

Mouse test shows jumpy movement, double clicks or a skipping wheel

  • The pointer jitters or jumps. Dust on the sensor or a glossy, glass or very uniform surface is the usual cause. Try a mouse pad and clean the sensor window.
  • A single press counts as a double click. A worn microswitch is typical on older mice. Compare the click counters in the test with how many times you actually pressed.
  • The scroll wheel skips or reverses. Dirt in the wheel encoder causes this. Short bursts of compressed air often help.
  • Wireless mouse lags. Check the battery level, move the receiver to a front USB port and keep it away from USB 3.0 hubs.

A controlled mouse troubleshooting sequence

Test on a clean, flat mouse pad and keep pointer speed and button settings unchanged while comparing results.

What you observeNext checkHow to interpret it
Pointer jumps or stallsClean the sensor window and test on a matte, non-glass surface.If tracking improves, the surface or sensor contamination was likely involved; if not, compare another USB port or computer.
Single click becomes a double clickMake ten deliberate single clicks with pauses between them.If extra click events recur across computers, a worn switch is more likely than a browser display issue.
Wheel skips or reversesScroll slowly in one direction, then repeat in the opposite direction.Irregular wheel deltas can come from debris or a worn encoder; browser event batching means the displayed delta is not a hardware calibration.
Side buttons do not appearTemporarily disable vendor remapping or profiles, then test again.Some software maps side buttons to navigation or macros before the browser receives the event.

Important: A browser-based check reports only the events and device information exposed to the page. Confirm suspected faults with another application, cable, peripheral or operating-system diagnostic before replacing hardware.

Mouse Test Online FAQ

Can the test measure my mouse DPI?

No. A higher DPI makes the coordinates change faster for the same hand movement, but the browser does not expose a DPI value.

Why does the middle button not register?

Vendor software or an OS setting may be using it for another action. Disable the remap and click the wheel again.

How accurate is the polling rate estimate?

It is approximate. Browsers batch pointer events, so treat the number as a relative comparison.

Is a smooth cursor proof the sensor is fine?

It is a good sign, but tracking problems often appear only on certain surfaces, so test on the surface you actually use.

Related PC hardware tests

Continue with the Touchpad Test Online, Keyboard Test Online, Gamepad Test Online, browse the PC hardware test guides, or run the whole suite from the PC Hardware Test Online homepage.