PCHardwareTest guide

Microphone Test Online

Start the microphone test to see a live waveform and level meter react to your voice, then record three seconds and play them back to hear exactly what your browser receives. Current level, peak level and an approximate noise floor help you decide whether the signal is too quiet, clipping or buried in room noise.

Start Microphone Test Online

Microphone Test Online

Live waveform, volume meter and a short recording playback.

Not started

Waiting to start.

Current level —
Peak level —
Approx. noise floor —

Audio is captured, analyzed and played back locally in your browser. Nothing is uploaded. A signal appearing on the meter means your browser can hear input — it is not a certified measurement of microphone quality.

Reading the meter

Current level follows your voice in real time and peak level holds the loudest moment. The noise floor is an estimate of the background level when you stay quiet. What matters is the gap between your speech peaks and that floor: a wide gap sounds clean, a narrow gap sounds hissy. A moving meter shows the browser can hear input, but it is not a certified measurement of microphone quality.

The three-second playback check

Press Record 3s, speak at normal volume about 20 cm from the microphone, then listen to the playback. Hum, hiss, popping or distortion on playback is what other people would hear. Audio is captured, analyzed and played back locally in your browser, and nothing is uploaded.

Picking the right input

Browsers show device names only after permission is granted. A laptop array microphone, a headset, a USB microphone and a webcam microphone can all be present at once, and selecting the wrong one is the most common reason for a flat meter. After choosing a device, speak again and watch for movement.

Microphone test shows no level, low volume or echo

  • The level bar never moves. The wrong input device may be selected, the input is muted in system sound settings, or the browser has blocked microphone access for this site.
  • The signal is very quiet. Raise the input gain in your operating system and move closer. The noise floor reading shows how loud the room is when you are silent.
  • Bluetooth headset sounds poor. Headsets drop to a low-quality call profile when the microphone is active. That is a Bluetooth limit, not a fault in the microphone.
  • Playback echoes or squeals. Play your recording through headphones so the speakers do not feed back into the microphone.

A practical microphone fault-isolation check

Use a quiet room and speak at a consistent distance. Select one input device at a time so that the meter and playback check refer to the microphone you intend to use.

What you observeNext checkHow to interpret it
The level meter stays stillCheck the browser permission icon, operating-system input privacy setting, mute switch and selected input.If another recording app also receives no signal, investigate the device, cable or driver. A blocked permission can look like a failed microphone.
The level is consistently lowMove to the recommended speaking distance and check the system input gain.Compare the same sentence at the same distance; automatic gain control can change the meter and makes casual comparisons unreliable.
Playback echoes or feeds backUse headphones and mute speakers during the recording check.If the echo disappears, acoustic feedback or loopback routing was likely involved rather than a defective microphone capsule.
Noise is present when silentDisconnect unnecessary audio devices and listen to a short quiet segment.Fan noise, room noise, cable interference and automatic processing can all raise the noise floor; the browser meter cannot identify the source.

Important: A browser-based check reports only the events and device information exposed to the page. Confirm suspected faults with another application, cable, peripheral or operating-system diagnostic before replacing hardware.

Microphone Test Online FAQ

Does this site upload my recording?

No. Recording, analysis and playback all happen locally in your browser.

Why is the input list empty until I allow access?

Browsers hide device names until you grant permission, to prevent sites from profiling your hardware.

How loud should the meter get when I speak?

Aim for peaks in the upper half of the meter without constantly touching the end, which suggests clipping.

Why is there a noise floor when I am silent?

Every microphone and room has some background noise, from fans, air conditioning or the microphone's own electronics.

Why is my microphone not working?

Check that the right input device is selected, that it is not muted in system sound settings and that the browser has permission. The troubleshooting list above covers each case.

Related PC hardware tests

Continue with the Webcam Test Online, Headphone Test Online, Speaker Test Online, browse the PC hardware test guides, or run the whole suite from the PC Hardware Test Online homepage.